web analytics

Which of the following are required components for Client MFP?

Which of the following are required components for Client MFP? (Choose two.) A. CCXv4 B. CCXv5 C. 802.11n D. WPA2 w/TKIP or AES-CCMP E. AnyConnect 3.0 Correct Answer: BD

Which three security threats require the Cisco Adaptive wIPS service for mitigation?

Which three security threats require the Cisco Adaptive wIPS service for mitigation? (Choose three.) A. on/off-channel rogue B. spectrum intelligence C. man-in-the-middle attack D. rogue switch-port tracing E. zero-day attack

You have been hired to install an outdoor wireless network for a small city. The design must provide 360 degrees of coverage from a central location and at least 33 Mb/s of aggregate bandwidth for clause 18 radio clients. How do you design this solution?

You have been hired to install an outdoor wireless network for a small city. The design must provide 360 degrees of coverage from a central location and at least 33

Which two UNII bands and channels should you restrict the APs to use on the 5 GHz radios?

You are designing an autonomous wireless network for an office building that is located near a local airport. The customer requires the use of 802.11a/n clients only, and the APs

Which of the following statements are not correct about Client Management Frame Protection (MFP)?

Which of the following statements are not correct about Client Management Frame Protection (MFP)? (Choose 2.) A. Client MFP can replace Infrastructure MFP in case only CCXv5 clients are used.

Which of the following statements are true regarding RLDP?

Which of the following statements are true regarding RLDP? (Choose two) A. RLDP works only on APs configured in Open Authentication mode. B. RLDP only works if the AP is

What is the best EAP method for XYZ to implement?

Corporation XYZ just underwent a third-party security audit. The auditors have required that the corporation implements 802.1x on its wireless network and disable all pre-shared key WLANs as soon as

Which of the below parameters are used in calculating the range – maximum distance – of an outdoor link between two bridges?

Which of the below parameters are used in calculating the range – maximum distance – of an outdoor link between two bridges? Choose two. A. The cable length between bridge

Which role does the Wi-Fi Alliance fulfill regarding WLANs?

Which role does the Wi-Fi Alliance fulfill regarding WLANs? A. creates global interoperability for wireless channels and spectrum B. maintains and creates the protocol standards by which wireless devices work

You are working for a South American services integrator. Your customer has a working unified Cisco WLC solution in Costa Rica (-A domain). You need to integrate an office in Panama (-N domain); correct APs are already deployed for this domain. Which approach do you take?

You are working for a South American services integrator. Your customer has a working unified Cisco WLC solution in Costa Rica (-A domain). You need to integrate an office in

Which environmental phenomena can cause considerable degradation to your wireless signals?

Which environmental phenomena can cause considerable degradation to your wireless signals? A. multipath, reflection, scattering, refraction B. multipath, alpha particles, diversity, absorption C. multipath, cosmic radiation, free path loss, scattering

Users complain about intermittent wireless connectivity issues. You see the following message on your Cisco WCS, corresponding the time the connectivity issues occurred. AP ‘building-1-entrance’, interface ‘802.11b/g’ on Controller ‘10.1.1.2’. Noise threshold violated. What do you do?

Users complain about intermittent wireless connectivity issues. You see the following message on your Cisco WCS, corresponding the time the connectivity issues occurred. AP ‘building-1-entrance’, interface ‘802.11b/g’ on Controller ‘10.1.1.2’.

The transmit power level on an 802.11a radio is configured for 25 mW. What is the corresponding value in decibels?

The transmit power level on an 802.11a radio is configured for 25 mW. What is the corresponding value in decibels? A. 2.5 dBm B. 3 dBm C. 14 dBm D.

When viewed from the side (in the H-plane), how can the radiation pattern of a patch and Yagi antennas be described? (Choose two.)

When viewed from the side (in the H-plane), how can the radiation pattern of a patch and Yagi antennas be described? (Choose two.) A. the patch patterns are egg-shaped. B.

On AIR-CAP3500 Series APs, which AP mode allows you to intensively analyze the frequency spectrum and detect interferers?

On AIR-CAP3500 Series APs, which AP mode allows you to intensively analyze the frequency spectrum and detect interferers? A. Sniffer B. Monitor C. SE-Connect D. Analyzer E. Rogue Detector Correct

One of your customers is thinking of deploying wireless in a building. Which two items should you establish in a pre-site survey? (Choose two.)

One of your customers is thinking of deploying wireless in a building. Which two items should you establish in a pre-site survey? (Choose two.) A. the exact channels that should

Your site has already been surveyed at 5 GHz for 802.11n VoWLAN services. Which services can you add safely, without conducting an additional site survey?

Your site has already been surveyed at 5 GHz for 802.11n VoWLAN services. Which services can you add safely, without conducting an additional site survey? (Choose two.) A. enhanced Layer

You are a wireless network administrator for a company that has installed a network that is based on Cisco WLC and uses Aironet 1140 Series APs. The clients are using the 2.4 GHz band and WPA TKIP for Layer 2 security. The president of the company reads a news article on the benefits of 802.11n and wants to deploy it at the office so that the company can use data rates of up to 150 Mb/s. What should you tell the president?

You are a wireless network administrator for a company that has installed a network that is based on Cisco WLC and uses Aironet 1140 Series APs. The clients are using

Which type of indoor Cisco AP should you deploy to make use of spatial multiplexing?

Which type of indoor Cisco AP should you deploy to make use of spatial multiplexing? A. AIR-LAP1242AG B. AIR-BR1310G C. AIR-LAP1131AG D. AIR-LAP1252AG E. AIR-LAP1524AG Correct Answer: D

What recommendation will have the greatest mitigation on the effects of 802.11b clients on the rest of the network?

After interviewing the customer to understand its wireless client requirements, you determine that 802.11b must be enabled to support legacy clients within a mixedmode environment. What recommendation will have the

ABC Company end users are reporting voice roaming issues. Which two situations are possible causes? (Choose two.)

ABC Company end users are reporting voice roaming issues. Which two situations are possible causes? (Choose two.) A. The RF coverage cells have only 10-percent overlap; 15- to 20-percent cell

Which regulatory body develops standards for European information and communication technologies?

Which regulatory body develops standards for European information and communication technologies? A. European Union B. European Telecommunications Standards Institute C. European Radio and Telecommunications Terminal Equipment Directive D. International Organization

You have been hired to conduct a predeployment indoor wireless site survey. Which item is not needed before starting the project?

You have been hired to conduct a predeployment indoor wireless site survey. Which item is not needed before starting the project? A. a statement of work that details the areas

Which three of these are considered Cisco RF guidelines for a proper VoWLAN deployment?

Which three of these are considered Cisco RF guidelines for a proper VoWLAN deployment? (Choose three.) A. Cell edge should be -67 dBm with 20 to 30 percent overlap. B.

Which feature would be helpful to prevent wireless internet access from 1 of the 25 buildings?

Corporation XYZ has 25 buildings (with a total of 12000 employees) and would like to implement a single SSID across their entire site. Which feature would be helpful to prevent

When conducting a greenfield RF site survey with multiple APs, which information element should be enabled to ensure your site survey software will display the hostname of each AP?

When conducting a greenfield RF site survey with multiple APs, which information element should be enabled to ensure your site survey software will display the hostname of each AP? A.

Which of the below devices can cause unintentional RF jamming attacks against an 802.11 wireless network?

Which of the below devices can cause unintentional RF jamming attacks against an 802.11 wireless network? (Choose two.) A. Rogue Access Points B. Microwave Oven C. Radar D. 900 Mhz

While reviewing data gathered during a passive RF site survey for an existing network of Cisco Aironet 1260 Series Access Points, you discover a high amount of potential co-channel interference throughout the network. Which two of these are potential causes? (Choose two.)

While reviewing data gathered during a passive RF site survey for an existing network of Cisco Aironet 1260 Series Access Points, you discover a high amount of potential co-channel interference

Which IEEE standard allows for the use of multiple 2-MHz communication channels within the 2.4-GHz spectrum?

Which IEEE standard allows for the use of multiple 2-MHz communication channels within the 2.4-GHz spectrum? A. 802.14 B. 802.15.4 C. 802.16.1 D. 802.18 E. 802.19 Correct Answer: B

You are tasked with creating a controller-based high-density RF design. Which three factors determine the cell size? (Choose three.)

You are tasked with creating a controller-based high-density RF design. Which three factors determine the cell size? (Choose three.) A. antenna type B. ClientLink support C. basic data rate D.

You are configuring an autonomous wireless guest network for your customer. The customer requires that guest users be unable to communicate with one another. Which solution best meets this requirement?

You are configuring an autonomous wireless guest network for your customer. The customer requires that guest users be unable to communicate with one another. Which solution best meets this requirement?

Which of these cannot be configured before you obtain the radio specifications?

You are tasked with designing a wireless network to support a specific 5-GHz wireless phone. During the initial design phase you are unable to obtain the client device radio specifications.

Which three general guidelines should be followed to overlay a Cisco Context-Aware Mobility Solution?

Company XYZ has a wireless network in place. Which three general guidelines should be followed to overlay a Cisco Context-Aware Mobility Solution? (Choose three.) A. The maximum effective AP spacing

Which two statements are not correct about client MFP?

Which two statements are not correct about client MFP? (Choose two.) A. Client MFP can replace infrastructure MFP if only CCXv5 clients are used. B. Client MFP encrypts class 3

Which of the below statement is correct with regards to configuring local MAC authentication on an AP?

Which of the below statement is correct with regards to configuring local MAC authentication on an AP? A. A MAC address can be spoofed, so it is insecure. B. The

What is the advantage of EAP-FAST compared to LEAP?

What is the advantage of EAP-FAST compared to LEAP? A. EAP-FAST exchanges user credentials within a TLS tunnel whereas LEAP exchanges credentials information in clear, which allows possible offline “dictionary

Which of the following is not a valid IPv6 address type?

Which of the following is not a valid IPv6 address type? A. link-local unicast B. unique-local unicast C. anycast D. multicast E. broadcast Correct Answer: E

Which three are equivalent forms of the IPv6 address 2011:0000:0000:0000:2010:0000:0000:000F?

Which three are equivalent forms of the IPv6 address 2011:0000:0000:0000:2010:0000:0000:000F? (Choose three.) A. 2011:0:0:0:2010:0:0:F B. 2011::2010::000F C. 2011:0:0000:0000:2010::000F D. 2011::2010:0:0:F E. 2011::201:0000:0000:000F F. 2011::201:0010:0010:000F Correct Answer: ACD

Which channels will you choose to make optimum use of the available spectrum?

You are designing a wireless infrastructure for an enterprise customer in the busy international banking district of Tokyo. All the client adapters are fairly modern, so you have turned off

Which two statements are true regarding the trust state configuration of a switch port?

To avoid classification at all switches within a QoS domain, a switch port may be configured in a trusted state. Which two statements are true regarding the trust state configuration

Which two protocols or processes can be used for a switched network to control distribution of multicast traffic at Layer 2?

Which two protocols or processes can be used for a switched network to control distribution of multicast traffic at Layer 2? (Choose two.) A. PIM B. CGMP C. IGMP v2

Which aggregate of the IPv6 addresses 2001:0303:0000:5000:0000:052B:0000:0000/96 and 2001:0303:0000:5000:0000:052C:0000:0000/96 has the longest possible mask?

Which aggregate of the IPv6 addresses 2001:0303:0000:5000:0000:052B:0000:0000/96 and 2001:0303:0000:5000:0000:052C:0000:0000/96 has the longest possible mask? A. 2001:0303:0000:5000:0000:052A:0000:0000/96 B. 2001:0303:0000:5000:0000:052A:0000:0000/95 C. 2001:0303:0000:5000:0000:0528:0000:0000/93 D. 2001:0303:0000:5000:0000:0520:0000:0000/92 Correct Answer: C

Which two statements about the IPv4 ToS byte are true?

Which two statements about the IPv4 ToS byte are true? (Choose two.) A. The ToS byte is located in the Layer 2 header. B. The ToS byte is located in

Which of the below DHCP options needs to be configured?

You have 2 WLCs with management IP addresses of 192.168.11.5 and 192.168.11.6 respectively. Your APs reside on a different subnet. Which of the below DHCP options needs to be configured?

Which three statements about the interface types of the controllers are true?

Cisco WiSM controllers have multiple interface types. Which three statements about the interface types of the controllers are true? (Choose three.) A. The service-port interface is the default interface for

Which configuration fulfills all the requirements?

A router has two interfaces: Ethernet 0 is connected to the LAN and Ethernet 1 is connected to the Internet. The LAN is 20.20.20.0/24. All hosts on the LAN must

When LAG is enabled, all ports participate in LAG by default. Which statement about LAG is true?

When LAG is enabled, all ports participate in LAG by default. Which statement about LAG is true? A. The failure of one link affects only management access, not traffic throughput.

IN CUWN, what DHCP option needs to be configured for APs to join specific WLCs, if the WLCs and APs reside in different subnets?

IN CUWN, what DHCP option needs to be configured for APs to join specific WLCs, if the WLCs and APs reside in different subnets? A. option 43 B. option 60

Cisco WiSM controllers have multiple interface types. Which two interfaces must be present and configured at setup time? (Choose two.)

Cisco WiSM controllers have multiple interface types. Which two interfaces must be present and configured at setup time? (Choose two.) A. virtual B. virtual gateway C. service port D. operator

Which three protocols does IEEE 802.1X access control allow until the client is authenticated?

Which three protocols does IEEE 802.1X access control allow until the client is authenticated? (Choose three.) A. Cisco Discovery Protocol B. VLAN Trunking Protocol C. Spanning Tree Protocol D. Extensible